Eytons' Earth: Natural & Alternative Medicine

[Foggy_Notion]

Hi all, hope this finds you in good health.

I purchased a generator and it worked fine.
I would only use it about once a week though.
It worked fine for 5 months.

One time I went to use it with the same distilled
water I always used, same silver wire.

And when I returned little black things were floating
in the water.

I threw it out and tried again and again, with different
water and got the same results.

Does anyone know why this is happeneing?

Because this makes me paranoid as can be
because it coincided with me becoming an
activist, bad mouthing the oil compnaies,
showing people how to make free electricity
using old Tesla patents, etc...

Well, they're powerfil people and I wouldn't
put it past them, if they feel someone was
stepping on their toes. Wait now I sound like
a nut, ha ha ha.

Have these black floating flakes in the water
occured with anyone else?

Thanks.





.

[eytonsearth]

Greetings,

It is most likely that your silver electrodes are degrading. Any jagged edges ( even ones so small that you can't really see them ) cause an uneven pull of silver ions off of the electrode as the electrons are travelling between both electrodes.

This eventually causes very obvious flaking.

With basic colloidal silver generators, it is very important to buff the electrodes between batches in order to minimize the amount of agglomerated silver ( "sparklies", flakes, etc. ) deposited into the distilled water.

Try to be certain that the electrodes are parallel to each other when in the water. This will help minimize the problem.

Of course, the bottom of the silver electrode "rods" are always a problem area. That is why silverpuppy.com switched to looped electrodes. You could always buy the looped silver electrodes from Ken at silverpuppy.com and tyr to rig them to work with the unit you purchased.

I hope this helped!

Kind Regards,

Jason

[aladin]

Hy to everybody
First, sorry for my poor english , I am Romanian and English is not my first language.

I have THE SAME QUESTION to the members of this forum...
I have an bone infection, and I want to cure with colloidal silver. I purchased 999 wire ( square in section), tap water and 4 ( 9 v batteries)..
Also I use 1mA diode

after 1 min it appeared small bubbles ,
after several minutes something white appears like this:
h##p://silverpuppy*com/resource/30seconds.jpg

but after another 1-2 minutes something like a black tree upside down , appeared at the end of that electrode......about 2-3 mm length
I runned the batteries for about 25 minutes....
That black tree had dropped down on the bottom of the recipient..
Sincerly I drinked..about 4 spoon of the liquid..
I avoided the "black tree"
all liquid was very very pale yellow, and some white...

Where is my mistake..?
also I did not understand from your previous post what do you mean by :
"Any jagged edges ." ( because of my english...can you explayn also in other words?_)

Thank you
and I need this water ...for my infection...
Regrds
Dan,
from Romania

[lifesilver]

hi dan from romanian
the problem you have is the water is dont use tap water you need distilled water, to make cs you can buy this from a hardware shop possibly baumax or suma its not the best quality as its normaly used for putting in car baterries, i live near severin and have seen it in a lot of hardware shops.... you can also make your own distiller or you can also go to a village in romania and see if you can use the distiller that they use for making pelinka / sweeka ,, if you do this make sure the boiling chamber is clean and the condencing pipe (the pipe that pases into the cool water is either stainless steel or possibly a plastic pipe would work, i dont know what the copper pipe would do but it might be ok [b]pleas if anyone knows reply to post
1 use apa distalata
2 keep the cup cleen you use for making it (dont use metal cup)
3 you have a low grade device and this will give you the best cs but it still works
i hope this helps leo

[aladin]

Since then i found distilled water... ( in Romania there is an only one producer for distilled water)

But still same result...a little better it look but if i let more than 20-30 min the reaction the water turn gray or white cloudy...
I have silver 999..
and I use variable 9-32 V generator, 1mA diode

the best technique i used is to boil the water in the meantime...it looks more clear but when I have the Tindall effect the water is a little clowdy.. ...
but i never received clear water or pale yellow watter with Tindall effect..

so I am afraid to drink it

Thank you ...
PS lifesilver ..are you romanian or you live near Romania..

[arn]

[The Silver Genie]

[arn]

For those people who have a system which does not reverse the polarity automatically, you can just do it manually if you find you are getting black particles.

Some people suggest scrubbing the electrodes. Reversing the polarity is effective, and much easier.